Searching for just a few words should be enough to get started. If you need to make more complex queries, use the tips below to guide you.
Purchase individual online access for 1 year to this journal.
Price: EUR 95.00Impact Factor 2024: 0.6
The journal International Shipbuilding Progress (ISP) was founded in 1954. Each year two issues appear (in March and September). Publications submitted to ISP should describe scientific work of high international standards, advancing subjects related to the field of Marine Technology, such as:
- Concept development
- General design of ships and offshore objects
- Ship and offshore structural design
- Hydro-mechanics and -dynamics
- Maritime engineering and machinery systems
- Production processes of all types of ships and other objects intended for marine use
- Production technology and material science
- Shipping science, economics, and all directly related subjects
- Ship operations
- Offshore and ocean engineering in relation to the marine environment
- Marine safety
- Efficiency, lifecycle, and environment
- Ice-related aspects for ships and offshore objects.
The contents of the papers may be of a fundamental or of an applied scientific nature and must be of the highest novelty and rigor.
Authors: Abramson, H. Norman | Dale, John M.
Article Type: Research Article
DOI: 10.3233/ISP-1961-87801
Citation: International Shipbuilding Progress, vol. 8, no. 78, pp. 57-61, 1961
Authors: Shearer, K.D.A. | Lynn, W.M.
Article Type: Research Article
Abstract: To provide accurate data on the wind resistance of certain modern ship designs, wind tunnel tests have been carried out on ( 1 / ( 60 th scale models of a tanker and two cargo ships and on ( 1 / ( 64 th scale and ( 1 / ( 128 th scale models of a modern passenger liner. The tanker and cargo-vessel models were tested in three conditions of loading, and the magnitude and direction of the resultant force and …moment about amidships for each complete model in the three conditions are given for a free stream tunnel velocity of 100 ft. per second over a range of relative wind from 0 to 180 deg. off the bow. These models were tested in a wind gradient. In the case of the modern passenger liner the larger model was tested in a wind-gradient condition and the smaller model in both the wind-gradient and uniform-wind conditions. The magnitude and direction of the resultant force and moment about amidships were measured. Two ( 1 / ( 128 th scale models were used for measuring the wind resistance in the uniform wind condition, one of them acting as a reflexion model. With the exception of the reflexion model all tests were carried out with the models in the boundary layer close to the tunnel roof. For the ( 1 / ( 64 th and ( 1 / ( 60 th scale models the resultant velocity gradient was considered to be reasonably close to the gradient obtained under natural conditions above the surface of the sea. The model results are shown in a non-dimensional form using an ahead resistance coefficient K, and are compared with some published data. Certain possible inaccuracies in applying the model results to the ship conditions are discussed. There are two appendices. The first considers the factors affecting the natural wind velocity gradient above the surface of the sea and the second gives results obtained from wind speed measurements made at various points on the models. Diagrams indicate possible serious errors in speed measurements due to poor siting of an anemometer. Show more
DOI: 10.3233/ISP-1961-87802
Citation: International Shipbuilding Progress, vol. 8, no. 78, pp. 62-80, 1961
Authors: Butler, G. | Ison, H.C.K.
Article Type: Research Article
Abstract: The paper describes an investigation, in collaboration with the British shipbuilding Research Association, on the corrosion of electrical resistance welded and of coated seamless tubes in sea-water using model fire-tube boilers. Previous results and the experimental equipment have already been fully described elsewhere. Welded tubes are susceptible to deep pitting and perforation particularly in the weld region and, in marked contrast to previous results with seamless tubes, this is not reduced by increasing the copper content of the steel. Possible reasons for this difference in behaviour are discussed. The corrosion of mild-steel tubes is markedly reduced by chromizing …or phosphating but not by aluminizing or aluminium spraying. No pitting was observed on chromized tubes but these tubes had unsuitable mechanical properties, having a tendency to split on expansion into the tube plates. There is some evidence that the protection afforded by phosphating is of a temporary nature. No wrought-iron tubes were available for experiment but several tubes with a long service life have been examined. Possible reasons for this extended life are discussed. Show more
DOI: 10.3233/ISP-1961-87803
Citation: International Shipbuilding Progress, vol. 8, no. 78, pp. 81-101, 1961
IOS Press, Inc.
6751 Tepper Drive
Clifton, VA 20124
USA
Tel: +1 703 830 6300
Fax: +1 703 830 2300
sales@iospress.com
For editorial issues, like the status of your submitted paper or proposals, write to editorial@iospress.nl
IOS Press
Nieuwe Hemweg 6B
1013 BG Amsterdam
The Netherlands
Tel: +31 20 688 3355
Fax: +31 20 687 0091
info@iospress.nl
For editorial issues, permissions, book requests, submissions and proceedings, contact the Amsterdam office info@iospress.nl
Inspirees International (China Office)
Ciyunsi Beili 207(CapitaLand), Bld 1, 7-901
100025, Beijing
China
Free service line: 400 661 8717
Fax: +86 10 8446 7947
china@iospress.cn
For editorial issues, like the status of your submitted paper or proposals, write to editorial@iospress.nl
如果您在出版方面需要帮助或有任何建, 件至: editorial@iospress.nl