Design of automatic urine collection system for medical system applications

1.Introduction

Urine examination is a kind of medical diagnostic method. Through the test of urine, doctors can obtain relevant information about the kidney and urinary system. Urine examination is a routine examination and is also the most common examination in nephrology. The results of urine tests are significant for clinical diagnosis, curative effect, and prognosis, providing valuable evidence across urology, antenatal health, diabetes, and increasingly certain cancers [1, 2, 3].

Urine tests are usually performed in hospitals or public health centers. The first step of the urine test is urine collection. At present, the primary collection method in urine test is to distribute disposable plastic urine cups by medical personnel, and the subjects take samples alone or accompanied by their family members. Because the examinees mainly control this process, there are often some factors, such as improper midstream urine collection time, urine spilling, and urine pollution, which lead to the increase of the test error. Besides, the plastic sampling cup is easy to bend and deform, which is not easy to operate, especially for women, the elderly, and the weak. In taking urine and finishing clothes, urine is easy to spill out of the container, causing hand or clothing pollution [4].

At present, most of the related research focuses on improving the testing instruments and the related personnel training. In contrast, the research on the collection process is relatively less. There are two types of designs related to urine collection in China [5, 6]. One is a simpler and cheaper sampling cup improved based on the original sampling cup. The sampling cup’s opening is usually funnel-shaped, and the lower part is connected to a urine cup through a catheter drainage; urine is thus collected through drainage. This kind of sampling cup partially solves the problem of urine splashing problems and inconvenient operations. However, its cost is higher than ordinary disposable plastic urine cups, so most hospitals do not widely use them. For example, the urine collection device produced by Qilu Hospital in Shandong, China, which uses sensors to identify whether the urine flows out or not, and controls the diversion by a magnet, can effectively intercept the interruption of urine. However, catheter cleaning is mainly through water flushing, which cannot completely ensure that urine is not contaminated. The other kind of design is to make sitting toilet intelligent and realize urine collection. By refitting the urine collection pipeline of the intelligent toilet, people can collect urine on the toilet. Alternatively, it is a collector made of sitting toilet shape; however, its cost is relatively high, and the equipment occupies a large area, so it is difficult to popularize in the squat toilet of most hospitals and public health examination centers [7, 8, 9].

Meanwhile, there are also many patents related to urine collection in other countries, even special collectors for women, children, and patients [10, 11, 12, 13]. For example, the collection underwear with drainage tube and collector, collectors of various shapes, and intelligent toilet, of course, can simultaneously complete sampling and testing and get the results [14, 15, 16, 17]. However, it is also difficult to promote in public places.

The collection system in this paper uses the STM32F103 microcontroller as the master controller [18, 19, 20]. It uses an infrared remote controll to control the motor to change the position of the urine cup, and the structure entirely fits the shape characteristics of plastic urine cups. It designs an automatic and easy-to-use human urine collection system for hospitals’ toilet environments and public physical examinations. It can maintain the physical examination environment of the public physical examination center to the greatest extent and it’s easy to maintain. There is no need to buy extra special-shaped urine cups. Which can save cost, ensure the accuracy of the test results, and improve the inconvenience of the collection process.

2.System structure design

2.2Structural composition

The urine collection system comprises an infrared remote control, a collection vehicle, and an external pedal. The infrared remote control is set on the toilet wall or door, convenient for users to operate. It sends control signals through function buttons to control the collection vehicle [21, 22, 23]. The collection vehicle is used to carry the urine cup and receive the infrared remote control’s signals to move forward and backward [24]. The external pedal is embedded in the collection vehicle to provide the mobile track. It needs to be placed on the squatting pan to carry the tested person during the collection process. The external pedal is embedded with a collection vehicle to provide a moving track for the vehicle and carry the subject during the acquisition process.

2.2.1Infrared remote control

The infrared remote controller that controls the vehicle movement mainly includes an infrared transmitter and five control buttons, namely Forward, Backward, Emergency Stop, One-button Acquisition, and Call for Rescue. The program controls the motor in the collection vehicle to achieve one-button acquisition functions, manual adjustment forward and backward movements, emergency stop, and rescue call.

2.2.2Collection vehicle

The collection vehicle is mainly used to carry the urine cup, control the urine cup movement and sampling automatically, and is the core component for realizing One-button acquisition. It is mainly composed of STM32F103 Microcontroller Unit (MCU), battery, infrared receiver, pressure sensor, metal ring, buzzer, four moving wheels, driving motor, and waterproof shell. Among them, the main chip, motor, and battery are all in the waterproof shell, and the infrared receiver is embedded in the shell to receive the infrared control signal and control the motor rotation and buzzer alarm. The front end of the shell is a metal ring for placing the urine cup. The diameter of the metal ring fits various commonly used urine cups, and the metal ring is connected by metal wires through the shell. A pressure sensor is arranged at the connection between the metal wires and the shell to judge the urine’s pressure value. When the pressure signal is greater than the preset threshold, stop sampling to avoid urine overflow.

Figure 1 shows the overall structure of the collection vehicle.

Figure 1.

Structure diagram of the collection vehicle.

2.2.3External pedal

The external pedal is placed above the squatting pan, and Fig. 2 shows the structure. It can support the subject without changing the toilet structure so that the urine passes through the opening of the pit and flows into the urine cup, which is carried by the carrying vehicle.

Figure 2.

Structure diagram of external pedal.

It takes into account the practical needs of the device to be exposed to a wet environment for a long time. To avoid the corrosion of urine, the whole pedal is made of non-toxic, odorless, tasteless, low temperature resistant, acid and alkali resistant, and low water absorption HDPE. It is placed on the two sides of the squatting pan, and the overall size of the pedal is suitable for most squatting toilets. The external pedal’s top surface has a pit opening, and both sides are used as a tread surface to support the tested person. Also, a metal ring can be selectively placed on the top surface. The metal ring’s diameter is larger than that on the collection vehicle, which can be used to control the position of ordinary disposable plastic urine cups and also can be used for funnel urine test cups. The pedal’s bottom provides two support parts corresponding to the tread position, supported on both sides of the squatting pan. The pedal’s inner sidewall has a moving track and a stop valve, whose width is the same as the wheel width of the collecting vehicle. The moving track plays a supporting role in collecting and carrying the vehicle, controlling the direction of movement and the fixed position.

3.Software design

The system uses the STM32F103 microcontroller with C language programming, according to the overall workflow, to determine the sequence of program operations. The main program calls the corresponding subroutines: infrared terminal decoding, motor forward driving, motor backward driving, motor constant driving, and delay subroutines.

According to the overall design, as Fig. 3 shows, the system’s program flow is as follows. First, initialize the system and the infrared interruption. Then the interruption scan is performed. When the button on the remote control is pressed, it sends out an infrared signal, and the infrared signal arrives at the infrared receiving module to trigger an external interruption. It then enters the infrared terminal decoding subprogram to decode and store the infrared signal. Next, the microcontroller outputs the corresponding control signal to control the stepper motor to be positive, reverse, or stop. When the “Rescue Call” button is pressed, the buzzer is controlled to sound the alarm.

Figure 3.

Flow chart of system program.

4.System validation

4.4Results

The scoring comparison of the two collections is shown in Table 1.

Table 1

Comparison of scores between the two groups

No.	Score		No.	Score		No.	Score		No.	Score
	First	Second		First	Second		First	Second		First	Second
T1	75	54	T17	58	6	T33	76	55	T49	72	57
T2	89	76	T18	88	62	T34	76	58	T50	76	68
T3	72	62	T19	62	50	T35	82	72	M1	88	65
T4	64	58	T20	83	73	T36	8	58	M2	7	57
T5	7	6	T21	84	64	T37	66	58	M3	88	68
T6	82	59	T22	73	70	T38	84	62	M4	62	50
T7	60	57	T23	88	77	T39	65	54	M5	75	63
T8	60	65	T24	62	52	T40	73	63	M6	84	64
T9	7	57	T25	72	61	T41	68	6	M7	62	52
T1	62	50	T26	85	65	T42	84	64	M8	72	61
T11	75	63	T27	68	57	T43	7	57	M9	73	63
T12	70	62	T28	75	67	T44	62	50	M1	76	58
T13	7	55	T29	68	57	T45	84	64	M11	72	61
T14	66	54	T3	73	62	T46	7	58	M12	66	6
T15	67	57	T31	72	65	T47	69	58
T16	85	6	T32	80	63	T48	80	66

The results are distributed according to different levels, and the results are shown in Fig. 4. It showed that for the tested person, 96% of the respondents thought that the system design was reasonable, and 22% thought that the system was troublesome to use; for the medical personnel, 91.7% thought that the sampling system was in line with the sampling requirements, and the pollution was small.

Table 2

Statistical analysis results of the two groups

	Average score	Standard deviation	t	P
Experimental group	73.30	8.33	13.937	0.000**
Control group	60.72	6.16

Figure 4.

Investigation results of human urine automatic collection system.

In addition, through the statistical analysis of the scores of the two groups, the results are shown in Table 2. Compared with the traditional acquisition mode, the average score of using the automatic acquisition system is higher. The paired sample mean test results show that the significance P is less than 0.05, indicated a significant difference. It shows that the automatic acquisition system is better than the traditional acquisition method.

5.Discussion

This article reports an automatic urine collection system for automatic urine collection at hospitals at all levels and public health examination centers. Unlike the urine collection device produced by Qilu Hospital in Shandong, China, the collection device does not contain a catheter, so it is unnecessary to clean the catheter and avoid sample contamination. Compared with the intelligent toilet, it is slightly inconvenient to use, but it is also more suitable for hospitals and public health examination centers with a large number of tests [4, 5, 6].

In this article, a comparison is made between using the device and not using it. The statistical results showed that there was a significant difference between the two groups. Although it is not very targeted to the collector for special populations [10, 11, 12, 13], it still has a high application value from the results. The device has low cost and good effect, and it can be popularized in public places compared with the intelligent toilet, which can complete sampling and testing simultaneously [14, 16].

Of course, because healthy people complete the testing process of the system, the safety and convenience of the special population need to be further tested. Although the evaluation is good, the objective evidence of whether the urine is not easy to be contaminated is still insufficient due to the subjective evaluation method. Therefore, the focus of the next step is to optimize the system further, improve the adaptability to the special population, and verify the pollution degree of the collected samples by using objective evidence. Before that, the test results can not be completely confirmed to be accurate, so the system is still in the experimental stage.

6.Conclusion

The system uses the STM32F103 single-chip computer as the central controller. It uses an infrared remote control to control the motor to adjust the position of the urine cup, thus realizing the automatic collection of human urine. It can also be adjusted manually according to the use situation and has an alarm function. The overall size is based on the squatting pan, which fits the size and shape characteristics of various disposable plastic urine cups, even not affected by the replacement of urine cups. It can realize an automatic collection of midstream urine under normal conditions, the manual collection under particular circumstances, emergency stop, and rescue call. Through the trial survey, there was a significant difference between the statistical results of using the device and not using the device (t= 13.937, P= 0.000). The trial evaluation is satisfactory and is suitable for hospitals at all levels and public health examination centers, where a large quantity of tests has to be performed, a shortage of medical personnel exists, or the process of urine collection cannot be strictly regulated. It can solve the test error caused by the nonstandard sampling and avoid embarrassment in a sampling operation. It has reasonable practicability and promotion value.